Center for Quantum Devices - Journal Articles and Conference Proceedings

Page 2 of 3: Prev << 1 2 3 >> Next (57 Items)

26.	Room temperature continuous wave operation of quantum cascade lasers with watt-level optical power Y. Bai, S.R. Darvish, S. Slivken, W. Zhang, A. Evans, J. Nguyen and M. Razeghi Applied Physics Letters, Vol. 92, No. 10, p. 101105-1-- March 10, 2008 We demonstrate quantum cascade lasers at an emitting wavelength of 4.6 µm, which are capable of room temperature, high power continuous wave (cw) operation. Buried ridge geometry with a width of 9.8 µm was utilized. A device with a 3 mm cavity length that was epilayer-down bonded on a diamond submount exhibited a maximum output power of 1.3 W at room temperature in cw operation. The maximum output power at 80 K was measured to be 4 W, with a wall plug efficiency of 27%. reprint
27.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, P. Sung, S.R. Darvish, W. Zhang, A. Evans, S. Slivken, and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000A-1-8.-- February 1, 2008 We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~ 4.75 µm. Ridge waveguides of 50 µm and 100 µm width were fabricated with both PCDFB and Fabry-Perot feedback mechanisms. The Fabry-Perot device has a broad emitting spectrum and a broad far-field character. The PCDFB devices have primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half-maximum of 4.8 degrees and 2.4 degrees for the 50 µm and 100 µm ridge widths, respectively. reprint
28.	Overview of Quantum Cascade Laser Research at the Center for Quantum Devices S. Slivken, A. Evans, J. Nguyen, Y. Bai, P. Sung, S.R. Darvish, W. Zhang and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000B-1-8.-- February 1, 2008 Over the past several years, our group has endeavored to develop high power quantum cascade lasers for a variety of remote and high sensitivity infrared applications. The systematic optimization of laser performance has allowed for demonstration of high power, continuous-wave quantum cascade lasers operating above room temperature. In the past year alone, the efficiency and power of our short wavelength lasers (~4.8 µm) has doubled. In continuous wave at room temperature, we have now separately demonstrated ~10% wallplug efficiency and ~700 mW of output power. Up to now, we have been able to show that room temperature continuous wave operation with > 100 mW output power in the 3.8 < λ < 11.5 µm wavelength range is possible. reprint
29.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, S.R. Darvish, S. Slivken, P. Sung, J. Nguyen, A. Evans, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 91, No. 14, p. 141123-1-- October 1, 2007 We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~4.75 µm. Ridge waveguides of 100 µm width were fabricated with both PCDFB and Fabry-Pérot feedback mechanisms. The Fabry-Pérot device has a broad emitting spectrum and a double lobed far-field character. The PCDFB device, as expected, has primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half maximum of 2.4°. This accomplishment represents the first step in power scaling of single mode, midinfrared laser diodes operating at room temperature. reprint
30.	Buried heterostructure quantum cascade lasers with high continuous-wave wall plug efficiency A. Evans, S.R. Darvish, S. Slivken, J. Nguyen, Y. Bai and M. Razeghi Applied Physics Letters, Vol. 91, No. 7, p. 071101-1-- August 13, 2007 The authors report on the development of ~4.7 µm strain-balanced InP-based quantum cascade lasers with high wall plug efficiency and room temperature continuous-wave operation. The use of narrow-ridge buried heterostructure waveguides and thermally optimized packaging is presented. Over 9.3% wall plug efficiency is reported at room temperature from a single device producing over 0.675 W of continuous-wave output power. Wall plug efficiencies greater than 18% are also reported for devices at a temperature of 150 K, with continuous-wave output powers of more than 1 W. reprint
31.	High-power mid- and far- wavelength infrared lasers for free space communication M. Razeghi; A. Evans; J. Nguyen; Y. Bai; S. Slivken; S.R. Darvish; K. Mi Proc. SPIE 6593, Photonic Materials, Devices, and Applications II, 65931V (June 12, 2007)-- June 12, 2007 Laser-based free-space communications have been developed to serve specific roles in "last mile" high-speed data networks due to their high security, low cost, portability, and high bandwidth. Conventional free-space systems based on near infrared optical devices suffer from reliability problems due to atmospheric scattering losses and scintillation effects, such as those encountered with storms, dust, and fog. Mid-infrared wavelengths are less affected by atmospheric effects and can significantly enhance link up-time and range. This paper will discuss some of the recent advances in high-power, high temperature, high reliability mid-infrared Quantum Cascade Lasers and their potential application in highly reliable free space communication links. reprint
32.	Current status of high performance quantum cascade lasers at the center for quantum devices M. Razeghi; A. Evans; Y. Bai; J. Nguyen; S. Slivken; S.R. Darvish; K. Mi Conference Proceedings - International Conference on Indium Phosphide and Related Materials. 588-593:[4266015] (2007)-- May 14, 2007 Mid-infrared laser sources are highly desired for laser-based trace chemical sensors, military countermeasures, free-space communications, as well as developing medical applications. While application development has been limited by the availability of adequate mid-infrared sources, InP-based quantum cascade lasers (QCLs) hold promise as inexpensive, miniature, portable solutions capable of producing high powers and operating at high temperatures with excellent beam quality and superior reliability. This paper discusses the most recent developments of application-ready high power (> 100 mW), continuous-wave (CW), mid-infrared QCLs operating above room temperature with lifetimes exceeding 13,000 hours. reprint
33.	High-power continuous-wave operation of distributed-feedback quantum-cascade lasers at λ ~ 7.8 µm S.R. Darvish, W. Zhang, A. Evans, J.S. Yu, S. Slivken, and M. Razeghi Applied Physics Letters, 89 (25)-- December 18, 2006 The authors present high-power continuous-wave (cw) operation of distributed-feedback quantum-cascade lasers. Continuous-wave output powers of 56 mW at 25 °C and 15 mW at 40 °C are obtained. Single-mode emission near 7.8 μm with a side-mode suppression ratio of >=30 dB and a tuning range of 2.83 cm⁻¹ was obtained between 15 and 40 °C. The device exhibits no beam steering with a full width at half maximum of 27.4° at 25 °C in cw mode. reprint
34.	Temperature dependent characteristics of λ ~ 3.8 µm room-temperature continuous-wave quantum-cascade lasers J.S. Yu, A. Evans, S. Slivken, S.R. Darvish and M. Razeghi Applied Physics Letters, 88 (25)-- June 19, 2006 The highest-performance device displays pulsed laser action at wavelengths between 3.4 and 3.6 μm, for temperatures up to 300 K, with a low temperature (80 K) threshold current density of approximately 2.6 kA/cm², and a characteristic temperature of T₀~130 K. The shortest wavelength QCL (λ ~ 3.05 μm) has a higher threshold current density (~12 kA/cm² at T=20 K) and operates in pulsed mode at temperatures up to 110 K. reprint
35.	Room-temperature, high-power and continuous-wave operation of distributed-feedback quantum-cascade lasers at λ ~ 9.6 µm S.R. Darvish, S. Slivken, A. Evans, J.S. Yu, and M. Razeghi Applied Physics Letters, 88 (20)-- May 15, 2006 High-power continuous-wave (cw) operation of distributed-feedback quantum-cascade lasers is reported. Continuous-wave output powers of 100 mW at 25 °C and 20 mW at 50 °C are obtained. The device exhibits a cw threshold current density of 1.34 kA/cm², a maximum cw wall-plug efficiency of 1% at 25 °C, and a characteristic temperature of ~190 K in pulsed mode. Single-mode emission near 9.6 μm with a side-mode suppression ratio of ≥ 30 dB and a tuning range of 2.89 cm^–1 from 15 to 50 °C is obtained. reprint
36.	High-power λ ~ 9.5 µm quantum-cascade lasers operating above room temperature in continuous-wave mode J.S. Yu, S. Slivken, A. Evans, S.R. Darvish, J. Nguyen, and M. Razeghi Applied Physics Letters, 88 (9)-- February 27, 2006 We report high-power continuous-wave (cw) operation of λ~9.5 μm quantum-cascade lasers to a temperature of 318 K. A high-reflectivity-coated 19-μm-wide and 3-mm-long device exhibits cw output powers as high as 150 mW at 288 K and still 22 mW at 318 K. In cw operation at 298 K, a threshold current density of 1.57 kA/cm², a slope efficiency of 391 mW/A, and a maximum wall-plug efficiency of 0.71% are obtained. reprint
37.	Quantum-Cascade Lasers Operating in Continuous-Wave Mode Above 90°C at λ ~5.25 µm A. Evans, J. Nguyen, S. Slivken, J.S. Yu, S.R. Darvish, and M. Razeghi Applied Physics Letters 88 (5)-- January 30, 2006 We report on the design and fabrication of λ~5.25 μm quantum-cascade lasers (QCLs) for very high temperature continuous-wave (CW) operation. CW operation is reported up to a maximum temperature of 90 °C (363 K). CW output power is reported in excess of 500 mW near room temperature with a low threshold current density. A finite element thermal model is used to investigate the G_th and maximum CW operating temperature of the QCLs. reprint
38.	Room-temperature continuous-wave operation of quantum-cascade lasers at λ ~ 4 µm J.S. Yu, S.R. Darvish, A. Evans, J. Nguyen, S. Slivken, and M. Razeghi Applied Physics Letters 88 (4)-- January 23, 2006 High-power cw λ~4 μm quantum-cascade lasers (QCLs) are demonstrated. The effect of different cavity length and laser die bonding is also investigated. For a high-reflectivity-coated 11-μm-wide and 4-mm-long epilayer-down bonded QCL, cw output powers as high as 1.6 W at 80 K and 160 mW at 298 K are obtained, and the cw operation is achieved up to 313 K with 12 mW. reprint
39.	High-Power Distributed-Feedback Quantum Cascade Lasers W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A.J. Evans, J.S. Yu, S.R. Darvish, S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 612704-- January 23, 2006 Recently, a distributed-feedback quantum cascade laser operating in a single spectral mode at 4.8 µm and at temperatures up to 333 K has been reported. In the present work, we provide detailed measurements and modeling of its performance characteristics. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single-mode at all currents and temperatures tested. Cw output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. reprint
40.	High Power, Continuous-Wave, Quantum Cascade Lasers for MWIR and LWIR Applications S. Slivken, A. Evans, J.S. Yu, S.R. Darvish and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 612703-- January 23, 2006 Over the past several years, our group has endeavored to develop high power quantum cascade lasers for a variety of remote and high sensitivity infrared applications. The systematic optimization of laser performance has allowed for demonstration of high power, continuous-wave quantum cascade lasers operating above room temperature. Since 2002, the power levels for individual devices have jumped from 20 mW to 600 mW. Expanding on this development, we have able to demonstrate continuous wave operation at many wavelengths throughout the mid- and far-infrared spectral range, and have now achieved >100 mW output in the 4.0 to 9.5 µm range. reprint
41.	Characterization and Analysis of Single-Mode High-Power CW Quantum-Cascade Laser W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A. Evans, J.S. Yu, S.R. Darvish, S. Slivken, and M. Razeghi Journal of Applied Physics 98-- October 15, 2005 We measured and modeled the performance characteristics of a distributed-feedback quantum-cascade laser exhibiting high-power continuous-wave (CW) operation in a single spectral mode at λ~4.8 µm and temperatures up to 333 K. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single mode at all currents and temperatures tested. CW output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. The slope efficiency and subthreshold amplified spontaneous emission spectra are shown to be consistent with a coupling coefficient of no more than κL ~ 4–5, which is substantially lower than the estimate of 9 based on the nominal grating fabrication parameters. reprint
42.	High-power, room-temperature and continuous-wave operation of distributed-feedback quantum-cascade lasers at λ = 4.8 µm J.S. Yu, S. Slivken, S.R. Darvish, A. Evans, B. Gokden and M. Razeghi Virtual Journal of Nanoscale Science and Technology 12 (5)-- August 1, 2005reprint
43.	High-power, room-temperature and continuous-wave operation of distributed-feedback quantum-cascade lasers at λ = 4.8 µm J.S. Yu, S. Slivken, S.R. Darvish, A. Evans, B. Gokden and M. Razeghi Applied Physics Letters, 87 (4)-- July 25, 2005 The authors present high-power continuous-wave (cw) operation of distributed-feedback quantum-cascade lasers. Continuous-wave output powers of 56 mW at 25 °C and 15 mW at 40 °C are obtained. Single-mode emission near 7.8 µm with a side-mode suppression ratio of >=30 dB and a tuning range of 2.83 cm⁻¹ was obtained between 15 and 40 °C. The device exhibits no beam steering with a full width at half maximum of 27.4° at 25 °C in cw mode. reprint
44.	Short Wavelength (λ~ 4.3 μm) High-Performance Continuous-Wave Quantum-Cascade Lasers J.S. Yu, A. Evans, S. Slivken, S.R. Darvish, and M. Razeghi IEEE Photonics Technology Letters, 17 (6)-- June 1, 2005 We report continuous-wave (CW) operation of a 4.3-μm quantum-cascade laser from 80 K to 313 K. For a high-reflectivity-coated 11-μm-wide and 4-mm-long laser, CW output powers of 1.34 W at 80 K and 26 mW at 313 K are achieved. At 298 K, the CW threshold current density of 1.5 kA/cm² is observed with a CW output power of 166 mW and maximum wall-plug efficiency of 1.47%. The CW emission wavelength varies from 4.15 μm at 80 K to 4.34 μm at 298 K, corresponding to a temperature-tuning rate of 0.87 nm/K. The beam full-width at half-maximum values for the parallel and the perpendicular far-field patterns are 26° and 49° in CW mode, respectively. reprint
45.	ZnO Thin Film Templates for GaN-based Devices D.J. Rogers, F. Hosseini Teherani, A. Yasan, R. McClintock, K. Mayes, S.R. Darvish, P. Kung, M. Razeghi and G. Garry SPIE Conference, Jose, CA, Vol. 5732, pp. 412-- January 22, 2005 GaN-based optoelectronic devices are plagued by a tendency to non-radiative transitions linked to defects in the active layers. ZnO is promising as a substrate material for GaN because it has the same wurtzite structure and a relatively small lattice mismatch (~1.8%). In this paper, we discuss use of ZnO thin films as templates for GaN based LED. reprint
46.	Review of III-Nitride Optoelectronic Materials for light Emission and Detection M. Razeghi, A. Yasan, R. McClintock, K. Mayes, D. Shiell, S. Darvish, and P. Kung Physica Status Solidi C S141 - S148-- September 10, 2004 We review the significant achievements relating to optoelectronic devices based on III-nitrides at the center for quantum devices (CQD). Based on GaN/InGaN multiple-quantum well structures, we demonstrated blue laser diodes at a wavelength of 405 nm. This achievement was particularly significant at the time, because while no defect reduction technique was used, a fairly low threshold current density was achieved (3.8 kA/cm²). In the past few years, however, the interest has shifted towards shorter wavelength light emitters, i.e. ultraviolet LEDs and LDs. Lower crystalline quality and unsatisfactory doping levels of AlGaN compound semiconductors posed serious challenges en route to the realization of UV light emitters. However, steady progress in the growth of AlGaN and AlN epilayers made it possible to overcome some of the difficulties. To date, we have been able to demonstrate UV LEDs at wavelengths as short as 265 nm (corresponding to 45% Al in Al_xGa_1-xN) with optical output powers of over 5 mW. We have addressed the n-type AlGaN doping problem by using a Si-In co-doped scheme. We also employed high-quality AlGaN/AlN superlattice templates for the reduction of defects. We have also demonstrated 280 nm UV LEDs with output powers of over 6 mW and external quantum efficiencies of over 0.25%. Despite all the success in the realization of short-wavelength UV LEDs, UV laser diodes at these short wavelengths are yet to be realized. The main difficulties are the low material quality, high device resistance leading to excessive heating of the device, realization of smooth cavity mirrors, and issues related to the cracking of the material. We have also demonstrated different types of photodetectors in the UV range of the spectrum: photoconductors, MSM photodetector, Schottky barrier photodetectors, and p-i-n photodiodes to name a few. The most promising type of photodetector for realization of UV imaging focal plane arrays is the p-i-n photodiode. Realization of high-efficiency AlGaN-based p-i-n photodiodes becomes more difficult when considering the need for the collection of the light from the backside of the substrate. However, similar to our back-emission UV LED structure, we have demonstrated back-illuminated p-i-n solar-blind photodiodes with external quantum efficiencies as high as 68% under no applied bias and 74% under -5 V of bias. reprint
47.	High Quantum Efficiency AlGaN Solar-Blind Photodetectors R. McClintock, A. Yasan, K. Mayes, D. Shiell, S.R. Darvish, P. Kung and M. Razeghi Applied Physics Letters, 84 (8)-- February 23, 2004 We report AlGaN-based back-illuminated solar-blind ultraviolet p-i-n photodetectors with a peak responsivity of 136 mA/W at 282 nm without bias. This corresponds to a high external quantum efficiency of 60%, which improves to a value as high as 72% under 5 V reverse bias. We attribute the high performance of these devices to the use of a very-high quality AlN and Al_0.87Ga_0.13N/AlN superlattice material and a highly conductive Si–In co-doped Al_0.5Ga_0.5N layer reprint
48.	High Power 280 nm AlGaN Light Emitting Diodes Based on an Asymmetric Single Quantum Well K. Mayes, A. Yasan, R. McClintock, D. Shiell, S.R. Darvish, P. Kung, and M. Razeghi Applied Physics Letters, 84 (7)-- February 16, 2004 We demonstrate high-power AlGaN-based ultraviolet light-emitting diodes grown on sapphire with an emission wavelength of 280 nm using an asymmetric single-quantum-well active layer configuration on top of a high-quality AlGaN/AlN template layer. An output power of 1.8 mW at a pulsed current of 400 mA was achieved for a single 300 µm×300 µm diode. This device reached a high peak external quantum efficiency of 0.24% at 40 mA. An array of four diodes produced 6.5 mW at 880 mA of pulsed current. reprint
49.	High Quantum Efficiency Solar-Blind Photodetectors R. McClintock, A. Yasan, K. Mayes, D. Shiell, S. Darvish, P. Kung and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 434-- January 25, 2004 We report AlGaN-based back-illuminated solar-blind p-i-n photodetectors with a record peak responsivity of 150 mA/W at 280 nm, corresponding to a high external quantum efficiency of 68%, increasing to 74% under 5 volts reverse bias. Through optimization of the p-AlGaN layer, we were able to remove the out-of-band negative photoresponse originating from the Schottky-like p-type metal contact, and hence significantly improve the degree of solar-blindness reprint
50.	Growth of Deep UV Light Emitting Diodes by Metalorganic Chemical Vapor Deposition A. Yasan, R. McClintock, K. Mayes, D. Shiell, S. Darvish, P. Kung and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 400-- January 25, 2004 We demonstrate high power AlGaN based ultraviolet light-emitting diodes (UV LEDs) with an emission wavelength of 280 nm using an asymmetric single quantum well active layer configuration on top of a high-quality AlGaN/AlN template layer grown by metalorganic chemical vapor deposition (MOCVD). An output power of 1.8 mW at a pulsed current of 400 mA was achieved for a single 300 µm × 300 µm diode. This device reached a high peak external quantum efficiency of 0.24% at 40 mA. An array of four diodes produced 6.5 mW at 880 mA of pulsed current. reprint

Page 2 of 3: Prev << 1 2 3 >> Next (57 Items)